Finding your thread size

In this guide

Thread size is the size of your wheel bolts or wheel studs, written as the diameter and the pitch, for example M12 x 1.5 or M14 x 1.5. The fixings for your Spacers have to match it.

In short

  1. Check whether your car has wheel bolts, or wheel nuts on studs.
  2. Measure across the thread with calipers. A little under 12mm is M12, and a little under 14mm is M14.
  3. Measure across 10 threads and divide by 10. That's the pitch, usually 1.25 or 1.5.

Rather not measure? Choose your car in the vehicle finder. It shows your car's thread size and whether it uses wheel bolts or wheel nuts.

DiameterPitchTapered seatThread

Before you start

  • Calipers, a measuring tool with sliding jaws and a reading, and a ruler marked in millimetres. A thread pitch gauge makes the pitch quicker to find.
  • To see the hub, take a wheel off. Park on level ground with the handbrake on, and support the car on axle stands, never just a jack.

Bolts or studs?

Look at the hub with the wheel off. If it has threaded holes, your car uses wheel bolts. If it has studs sticking out, it uses wheel nuts on studs. Either way, the thread size is the size of the bolt or the stud.

Wheel boltWheel studWheel nut

The diameter

The number after the M is the diameter of the thread in millimetres. Measure across the outside of the thread with calipers. It will read a little under the size, so 11.8mm is M12 and 13.8mm is M14. Most cars use M12 or M14.

The pitch

The pitch is the distance from one thread to the next, in millimetres. On wheel bolts and studs it's usually 1.25 or 1.5.

  1. Hold a ruler along the thread.
  2. Measure from the tip of one thread to the tip of the tenth thread after it.
  3. Divide it by 10. 15mm across 10 threads is a 1.5 pitch, and 12.5mm is a 1.25 pitch.
10 threads15mm across 10 threadsis a 1.5 pitch

A thread pitch gauge is quicker. Try the blades on the thread until one sits in it with no gaps, then read the size on the blade.

Inch threads

Some cars, mostly American and older British ones, have threads sized in inches, written like 1/2-20 UNF. That's 1/2in across, with 20 threads to every inch. An inch is 25.4mm, so to check, count the threads along 25.4mm of a ruler, or use a pitch gauge marked in threads per inch.

The threads we make

  • M12x1.25 and M12x1.5
  • M14x1.25, M14x1.5 and M14x2
  • M16x1.5
  • 3/8"-24 UNF, 7/16"-20 UNF and 1/2"-20 UNF

M14x1.25 isn't made with wheel nuts on studs. If your thread isn't listed, send us a message.

The seat

Bolts and nuts also have a seat, the part that sits against the wheel. Most aftermarket wheels take a 60° tapered seat, while many original wheels, such as those on VW, Audi and Mercedes, take a ball seat. A tapered seat is a straight-sided cone, and a ball seat is rounded. Some original Toyota and Lexus wheels take a flat seat nut with a washer. The seat has to match your wheels.

Our Spacers and Adapters are all made with a 60° tapered seat, so every bolt and nut we supply to fix them to your hub has a 60° tapered seat. The bolts or nuts that hold your wheel on still need to match your wheels.

When you order

In the builder, step 4, Hub side (your car), asks whether your car uses wheel bolts or wheel nuts, and its thread size. For a Bolt On Spacer or a PCD Adapter, step 5, Wheel side (your wheels), asks the same for the bolts or nuts that hold your wheel on. On a Bolt On Spacer they're usually the same as your car's. On a PCD Adapter they match the wheels you're fitting.

Our ready-made Spacers show the thread in the name, for example M14x1.5.

Find Spacers for your car

Pick your car, or build your own to your measurements.